Item is in stock and usually ships same day if orders are place before 8pm Eastern Standard Time
Free Shipping on all orders over $1000
Expedited shipping available for additional cost
Shipping rates available in shopping cart
Product may be returned if unopened and unused within 7 days of purchase
Returns after 7 days or for products that demonstrate usage will not be accepted for returns but accepted as warranty repairs only
General data
Frequency range
VHF: 136 - 174MHz ; UHF1: 400 - 470MHz
UHF2: 450-520MHz ; UHF3: 350 - 400MHz
Channel capacity
16
Channel spacing (analog)
12.5 / 20 / 25 kHz
Operating voltage
13.6 ± 15% VDC
Max. power consumption (in stand by)
≤ 0.8 A
Max. power consumption (during transmission)
≤ 11 A
Frequency stability
±0.5 ppm
Antenna impedance
50 Ω
Duty Cycle100%
Dimensions (H × W × D)
3.46 x 19 x 14.4 inches
Weight
18.74lbs
Transmitter
RF Power Output
5 – 50 W (adjustable)
FM Modulation
(Analog Emissions Designator)
11K0F3E at 12.5 kHz
14K0F3E at 20 kHz
16K0F3E at 25 kHz
4FSK Digital Modulation
(Digital Emissions Designator)
12.5 kHz (data only): 7K60FXD
12.5 kHz (data and voice): 7K60FXW
Conducted/Radiated Emission
-36 dBm < 1 GHz
-30 dBm > 1 GHz
Modulation limiting
±2.5 kHz at 12.5 kHz
±4.0 kHz at 20 kHz
±5.0 kHz at 25 kHz
FM Hum & Noise
40 dB at 12.5 kHz
43 dB at 20 kHz
45 dB at 25 kHz
Adjacent Channel Power
60 dB at 12.5 kHz
70 dB at 20/25 kHz
Audio Response
+1 dB to -3 dB
Audio distortion
≤ 3 %
Digital vocoder type
AMBE++ or SELP
Digital ProtocolETSI-TS102 361-1, 2 & 3
Receiver
Sensitivity (analog)
0.3 μV (12 dB SINAD)
0.22 μV (typical) (12 dB SINAD)
0.4 μV (20 dB SINAD)
Sensitivity (digital)
0.3 μV / BER 5%
Selectivity
TIA-603 ETSI
65 dB at 12.5 kHz / 75 dB at 20 and 25 kHz
60 dB at 12.5 kHz / 70 dB at 20 and 25 kHz
Intermodulation
TIA-603 ETSI
75 dB at 12.5/20/25 kHz
70 dB at 12.5/20/25 kHz
Spurious Response Rejection
TIA-603 ETSI
80 dB at 12.5/20/25 kHz
80 dB at 12.5/20/25 kHz
S/N
40 dB at 12.5 kHz
43 dB at 20 kHz
45 dB at 25 kHz
Rated Audio Power Output
0.5 W
Rated Audio Distortion
≤ 3 %
Audio Response
+1 dB to -3 dB
Conducted Spurious Emission
< -57 dBm
Environmental Specs
Operating temperature range
-30 °C to +60 °C
Storage temperature range
-40 °C to +85 °C
All technical indications were tested according to the corresponding standards. Subject to change on the basis of continuous development.
Dual Mode: Analog & Digital
Dual Mode Analog and Digital channel auto switching, allowing efficient frequency sharing between Analog and Digital users and ensures a smooth transition to Digital technology.
50W High Power
Maximum repeating power of 50W, and thus increasing the system coverage with lesser setup equipments.
16 Channels
A maximum of 16 channels, allowing efficient radio network control at different scenarios. The channel change can be performed either via RDAC PC tools, via the repeater’s front panel channel knob and via the channel steering from the repeater’s rear port.
Heat Dissipation
The unique cooling design combining a built-in heat pipe and a temperature-controlled fan ensures quick heat dissipation, enabling the repeater to operate efficiently even with full power.
Management Software
With the management software, you can remotely monitor and diagnose a repeater. In addition, you can either record or play back the audio freely in digital mode.
Innovative LED Design
The innovative LED and the 2.0” HD color display would deliver the repeater status clearly.
Expansion Ports
This allows third parties to develop accessory and applications via front and rear port of the repeater. This is achieved via the signal streaming and pin control through the repeater ports.
Dual Slot Digital Audio Streaming
Streaming of both the voice slots via the rear port accessory pins, allowing third party for capability expansion.
Continuous Wave Identification (CWID)
Analog transmission of the repeater identification in Morse code format.
Analog Scan
Analog voice and signaling scan, allowing coverage of different analog voice users from various groups.
le Sites Via IP
Multiple Sites Via IP
Network connection via the IP port of the repeater to form a private radio network to meet data and voice communication needs for wide-area coverage and dispersed locations.
Advanced TDMA Technology
The application of Time Division Multiple Access (TDMA) technology greatly enhances spectrum efficiency, which allows twice the users compared with that of traditional FDMA. Obviously, this can not only save infrastructure cost and frequency licenses, but also relieve the pressure of increasing shortage in spectrum resources.
Repeater Diagnostic And Control (RDAC)
Remote IP connection to monitor, diagnose, and control the repeater thus increasing maintenance efficiency. The Hytera developed RDAC is able to support multiple master network connections to allow the radio administrator to monitor multiple radio networks.
Interoperability
Two repeaters can be interconnected to provide interoperability between UHF and VHF. A single repeater can auto switch between Analog and Digital mode, allowing for efficient frequency sharing between Analog and Digital users and an easy digital migration.
Multi SS/CDCSS Decode
Decoding up to a maximum of 16 CDCSS/CTCSS codes in Analog channels allowing coverage for different Analog voice users from various groups.
Repeater Access Management
The repeater access control feature ensures a more secure network by preventing unauthorized users from accessing the radio network.
Analog/Digital Telephone Interconnect (via DTMF signaling)
Simplex voice communications between radio and telephone users. It allows a radio user to make a telephone call; or a telephone user to make either a Group or Private call to radio users. This feature utilizes the Commercial Off The Shelf (COTS) Analog Phone Patch boxes and a Plain Old Telephone Service (POTS) line to connect the Repeater to the Corporate Office Phone System (PBX) or Public Switched Telephone Network (PSTN).
Analog Repeater Knockdown
Repeater knockdown, that when activated via the repeater’s rear accessory pin, will disabled the transmit path of the repeater.
